Bc-technologies A-Computer Programming (HE Series) Uživatelský manuál Strana 1

Washer-ExtractorA-computer Programmingand Operating InstructionsB&C TechnologiesPanama City, FL(850) 249-2222(850) 249-2226 FAXwww.bandctech.comRe

10. The A-computer energizes supply 4 anddisplays " ". Hold this state until operatorS4presses advance (up+down).11. The A-computer energiz

ProgrammingThe computer board is located inside thecontrol module. In the middle of the board is asmall toggle switch used to change from Runmode to

ProgrammingSetup ModeThe setup options are programmable optionsthat are in operation during all wash cycles.The options are:> Temperature displayed

ProgrammingCycle Programming (continued)When modifying a cycle time, a time must beentered for each segment. To skip a segment orspin, enter for the

ProgrammingCycle Programming (continued)After selecting your desired supply option, pressthe Start key.If your machine is equipped with Auxiliaryheati

Cycle Segment Charts (continued)ProgrammingDetailsUse Up or Down to change. Start key is enter or advance00 or 02-30 Segment time: 00 to skip, or any

Cycle Segment Charts (continued)ProgrammingDetailsUse Up or Down to change. Start key is enter or advance00 or 02-30 Segment time: 00 to skip, or any

ProgrammingBlank Cycle ChartProgram NumberSegment Detail Segment DetailPrewasy/Flush Spray/DilutionTime (min) Time (min)Water Temp Water TempWater Lev

Factory ProgramsProgram Number: 1Segment Detail Segment DetailPrewasy/Flush Spray/DilutionTime (min) 05 Time (min) 00Water Temp cfil Water TempWater L

Factory Programs18Program Number: 2Segment Detail Segment DetailPrewasy/Flush Spray/DilutionTime (min) 05 Time (min) 00Water Temp bfil Water TempWater

Factory Programs19Program Number: 3Segment Detail Segment DetailPrewasy/Flush Spray/DilutionTime (min) 05 Time (min) 00Water Temp hfil Water TempWater

Factory Programs20Program Number: 6Segment Detail Segment DetailPrewasy/Flush Spray/DilutionTime (min) 00 Time (min) 00Water Temp Water TempWater Leve

Factory Programs21Program Number: 7Segment Detail Segment DetailPrewasy/Flush Spray/DilutionTime (min) 20 Time (min) 02Water Temp hfil Water Temp bfil

Factory Programs22Turnout Gear - Firehouse Duty Machines OnlyProgram Number 8Segment Detail Segment DetailPrewasy/Flush prew Spray/DilutionTime (min)

Table of ContentsIntroductionCustomer ServiceReplacement PartsSafety InformationKey SymbolsImportant Safety InformationOperationCycle SelectionCycle E

IntroductionLED DisplayCycleUpCycleDownStopStartA-computerThe A-computer is a powerful and versatilesolid state control. Up to 30 programs can bestor

.Anyone operation or servicing this machine must follow the safety rules inthis manual. Particular attention must be paid to the DANGER,WARNING, and C

Important Safety InformationSAFETY CHECK LISTBefore Initial start up of a washer – extractorperform the following safety check:A. Make sure all electr

Display Meaning Display Meaningb01ROM code. Example only.FLUSOverflow prewash selectedHoldWait - machine just powered upCFILCold FillCY01Cycle number

OperationCycle Execution (continued)Each of the 30 cycles consists of 8 segments. Atypical cycle has Prewash, Wash, and Rinses(up to six are availabl

OperationCycle Execution (continued)Stop RoutineWhen the final spin of the wash cycle iscomplete, the stop routine is activated. Thestop routine sequ