Bc-technologies B-Computer Programming (HE Series) Uživatelský manuál Strana 1

Washer-ExtractorB-Computer Programming and Operating InstructionsB&C TechnologiesPanama City, FL(850) 249-2222(850) 249-2226 FAXwww.bandctech.comR

ProgrammingJ3370555 20MADE IN USAMMATSJ2J1FLIP SWITCHFOR PROGRAMMODEThe computer board is located inside the control module. In the middle of the boa

ProgrammingSetup ModeThe setup options are programmable options that are in operation during all wash cycles. The options are:> Temperature displa

ProgrammingCycle Programming (continued)When modifying a cycle time, a time must be entered for each segment. To skip a segment or spin, enter 00 for

ProgrammingCycle Programming (continued)After selecting your desired supply option, press the Start key.If your machine is equipped with Auxiliary hea

Cycle Segment Charts (continued)ProgrammingDetailsUse Up or Down to change. Start key is enter or advance00 or 02 - 30 Segment time: 00 to skip, or

Cycle Segment Charts (continued)ProgrammingDetailsUse Up or Down to change. Start key is enter or advance00 or 02 - 30 Segment time: 00 to skip, or

ProgrammingBlank Cycle ChartProgram NumberSegment Detail Segment DetailPrewasy/Flush Spray/DilutionTime (min) Time (min)Water Temp Water TempWater Lev

Factory ProgramsProgram Number: 1S e gm e n t D e t ail S e gm e n t D e t ailPrewasy/Flush Spray/DilutionTime (min) 05 Time (min) 00Water Temp cfil W

Factory Programs17Program Number: 2S e gm e n t D e t ail S egm en t D e t ailPrewasy/Flush Spray/DilutionTime (min) 05 Time (min) 00Water Temp bfil W

Factory Programs18Program Number: 3S e gm e n t D e t ail S egm en t D e t ailPrewasy/Flush Spray/DilutionTime (min) 05 Time (min) 00Water Temp hfil W

Factory Programs19Program Number: 6S e gm e n t D e t ail S egm en t D e t ailPrewasy/Flush Spray/DilutionTime (min) 00 Time (min) 00Water Temp Water

Factory Programs20Program Number: 7S e gm e n t D e t ail S egm en t D e t ailPrewasy/Flush Spray/DilutionTime (min) 20 Time (min) 02Water Temp hfil W

Table of ContentsIntroductionCustomer ServiceReplacement PartsSafety InformationKey SymbolsImportant Safety InformationOperationCycle SelectionCycle E

IntroductionLED DisplayCycle UpCycle DownStopStartB-ComputerThe B-computer is a powerful and versatile solid state control. Up to 30 programs can be

. Anyone operation or servicing this machine must follow the safety rules in this manual. Particular attention must be paid to the DANGER, W

Important Safety InformationSAFETY CHECK LISTBefore Initial start up of a washer – extractor perform the following safety check:A. Make sure all elect

Display Meaning Display MeaningS04ROM code. Example only.FLUSOverflow prewash selectedHoldWait - machine just powered upCFILCold FillCYCycle number (

OperationCycle Execution (continued)Each of the 30 cycles consists of 8 segments. A typical cycle has Prewash, Wash, and Rinses (up to six are availa

OperationCycle Execution (continued)Stop RoutineWhen the final spin of the wash cycle is complete, the stop routine is activated. The stop routine se